Instruction Set Architecture

1. The ISA is the interface between the software and hardware.
2. It is the set of instructions that bridges the gap between high level languages and the hardware.
3. For a processor to understand a command, it should be in binary and not in High Level Language. The ISA encodes these values.
4. The ISA also defines the items in the computer that are available to a programmer. For example, it defines data types, registers, addressing modes, memory organization etc.
5. Register are high speed storage for numbers that can be accessed by a processor. Data as well as instructions can be in a register.

Addressing modes are the ways in which the instructions locate their operands.
Memory organization defines how instructions interact with the memory.

[edit] Computer Organization

Computer organization helps optimize performance-based products. For example, software engineers need to know the processing ability of processors. They may need to optimize software in order to gain the most performance at the least expense. This can require quite detailed analysis of the computer organization. For example, in a multimedia decoder, the designers might need to arrange for most data to be processed in the fastest data path.
Computer organization also helps plan the selection of a processor for a particular project. Multimedia projects may need very rapid data access, while supervisory software may need fast interrupts.
Sometimes certain tasks need additional components as well. For example, a computer capable of virtualization needs virtual memory hardware so that the memory of different simulated computers can be kept separated.
The computer organization and features also affect the power consumption and the cost of the processor.

[edit] Design goals

The exact form of a computer system depends on the constraints and goals for which it was optimized. Computer architectures usually trade off standards, cost, memory capacity, latency and throughput. Sometimes other considerations, such as features, size, weight, reliability, expandability and power consumption are factors as well.
The most common scheme carefully chooses the bottleneck that most reduces the computer's speed. Ideally, the cost is allocated proportionally to assure that the data rate is nearly the same for all parts of the computer, with the most costly part being the slowest. This is how skillful commercial integrators optimize personal computers.

[edit] Performance

Computer performance is often described in terms of clock speed (usually in MHz or GHz). This refers to the cycles per second of the main clock of the CPU. However, this metric is somewhat misleading, as a machine with a higher clock rate may not necessarily have higher performance. As a result manufacturers have moved away from clock speed as a measure of performance.
Computer performance can also be measured with the amount of cache a processor has. If the speed, MHz or GHz, were to be a car then the cache is like the gas tank. No matter how fast the car goes, it will still need to get gas. The higher the speed, and the greater the cache, the faster a processor runs.^{[dubious – discuss]}
Modern CPUs can execute multiple instructions per clock cycle, which dramatically speeds up a program. Other factors influence speed, such as the mix of functional units, bus speeds, available memory, and the type and order of instructions in the programs being run.
There are two main types of speed, latency and throughput. Latency is the time between the start of a process and its completion. Throughput is the amount of work done per unit time. Interrupt latency is the guaranteed maximum response time of the system to an electronic event (e.g. when the disk drive finishes moving some data). Performance is affected by a very wide range of design choices — for example, pipelining a processor usually makes latency worse (slower) but makes throughput better. Computers that control machinery usually need low interrupt latencies. These computers operate in a real-time environment and fail if an operation is not completed in a specified amount of time. For example, computer-controlled anti-lock brakes must begin braking almost immediately after they have been instructed to brake.
The performance of a computer can be measured using other metrics, depending upon its application domain. A system may be CPU bound (as in numerical calculation), I/O bound (as in a webserving application) or memory bound (as in video editing). Power consumption has become important in servers and portable devices like laptops.
Benchmarking tries to take all these factors into account by measuring the time a computer takes to run through a series of test programs. Although benchmarking shows strengths, it may not help one to choose a computer. Often the measured machines split on different measures. For example, one system might handle scientific applications quickly, while another might play popular video games more smoothly. Furthermore, designers have been known to add special features to their products, whether in hardware or software, which permit a specific benchmark to execute quickly but which do not offer similar advantages to other, more general tasks